?

十大玩彩信誉平台

?

丹佛斯FC302变频器故障代码和报警参数说明

时间:2020-01-10    编辑:津信变频    点击:
丹佛斯FC300系列变频器是丹佛斯推出的主力机型变频器,功率范围覆盖0.25KW到1.4MW,适用于各个行业的多种应用场合。在使用过程中如果出现故障,FC300变频器会在面板显示故障代码,以便分析故障原因和采取措施,故障代码含义如下:


故障代码 故障描述 Warning Alarm/Trip Alarm/Trip Lock
1 10 Volts low10伏电压低 X    
2 Live zero error断线故障 (X) (X)  
3 No motor无电机 (X)    
4 Mains phase loss主电源缺箱 (X) (X) (X)
5 DC link voltage high直流回路电压高 X    
6 DC link voltage low直流回路电压较低 X    
7 DC over-voltage直流过电压 X X  
8 DC under voltage直流欠电压 X X  
9 Inverter overloaded逆变器过载 X X  
10 Motor ETR over temperature电动机ETR 温度高 (X) (X)  
11 Motor thermistor over temperature电机热敏电阻温度高 (X) (X)  
12 Torque limit转矩限制 X X  
13 Over Current过电流 X X X
14 Earth Fault接地故障 X X X
15 Hardware mismatch硬件不匹配   X X
16 Short Circuit短路   X X
17 Control word time-out控制字超时 (X) (X)  
22 Hoist Mech. Brake起重机械制动 (X) (X)  
23 Internal Fan Fault内部风扇故障 X    
25 Brake resistor short-circuited制动电阻短路 X    
26 Brake resistor power limit制动电阻功率限制 (X) (X)  
27 Brake chopper short-circuited制动斩波器短路 X X  
28 Brake check刹车检查 (X) (X)  
29 Heatsink temp散热片温度 X X X
30 Motor phase U missing电动机缺U相 (X) (X) (X)
31 Motor phase V missing电机缺V相 (X) (X) (X)
32 Motor phase W missing电机缺W相 (X) (X) (X)
33 Inrush Fault充电故障   X X
34 Fieldbus communication fault现场总线通讯故障 X X  
36 Mains failure电源故障 X X  
37 Phase imbalance相位不平衡   X  
38 Internal Fault内部故障   X X
39 Heatsink sensor散热片传感器   X X
40 Overload of Digital Output Terminal 2727过载的数字输出终端 (X)    
41 Overload of Digital Output Terminal 2929过载的数字输出终端 (X)    
45 Earth Fault 2接地故障2 X X X
46 Pwr. card supply功率卡电源   X X
47 24 V supply low24 V电源低 X X X
48 1.8 V supply low1.8 V电源低   X X
49 Speed limit速度限制 X    
50 AMA calibration failedAMA校准失败   X  
51 AMA check Unom  and InomAMA检查Unom和Inom   X  
52 AMA low InomAMA低Inom   X  
53 AMA motor too bigAMA电机太大   X  
54 AMA motor too smallAMA电机太小   X  
55 AMA parameter out of rangeAMA参数范围   X  
56 AMA interrupted by userAMA用户中断   X  
57 AMA time-outAMA超时   X  
58 AMA internal faultAMA内部故障 X X  
59 Current limit电源极限 X    
60 External Interlock外部互锁 X X  
61 Feedback Error反馈错误 (X) (X)  
62 Output Frequency at Maximum Limit最大限度的输出频率 X    
63 Mechanical Brake Low机械制动器低   (X)  
64 Voltage Limit电压限制 X    
65 Control Board Over-temperature控制板保护套 X X X
66 Heat sink Temperature Low散热器温度低 X    
67 Option Configuration has Changed选择配置发生了变化   X  
68 Safe Stop安全停止 (X) (X)1)  
69 Pwr. Card Temp功率卡温度   X X
70 Illegal FC configuration非法FC配置     X
73 Safe Stop Auto Restart安全停止自动重启 (X) (X)  
76 Power Unit Setup功率卡设置 X    
77 Reduced power mode精简功率模式 X    
78 Tracking Error跟踪误差 (X) (X)  
79 Illegal PS config非法PS配置   X X
80 Drive Initialized to Default Value驱动初始化为默认值   X  
81 CSIV corruptCSIV破坏   X  
82 CSIV  parameter  errorCSIV 参数错误   X  
85 Profibus/Profisafe  Error现场总线/ Profisafe错误   X  
90 Feedback Monitor反馈监控 (X) (X)  
91 Analogue input 54 wrong settings模拟输入54错误设置     X
250 New spare part新备件     X
251 New Type Code新类型代码   X X



返回列表
?
XML 地图 | Sitemap 地图